-
1 многожильный кабель
многожильный кабель
многожильный провод
многожильный шнур
Кабель (провод, шнур), в котором число жил более трех.
[ ГОСТ 15845-80]EN
multicore cable
cable having more than one core
Note – The French term «câble multipolaire» is more specifically used to designate the cable constituting the phases of a multiphase system (example: three-core cable).
[EV ref 461-06-04]
multiconductor cable
cable having more than one conductor, some of which may be uninsulated
[IEV ref 461-06-03]FR
câble multiconducteur
câble multipolaire
câble comprenant plus d'un conducteur isolé
Note – Le terme câble multipolaire est plus particulièrement utilisé pour désigner le câble constituant les phases d'un système polyphasé (exemple: câble tripolaire).
[EV ref 461-06-04]
câble multiconducteur
câble multipolaire
câble comprenant plus d'une âme, dont éventuellement certaines non isolées
[IEV ref 461-06-03]
Core - (токопроводящая) жила;
Insulator - изоляция жилы;
Protective Sheath - оболочка кабеля.Недопустимые, нерекомендуемые
Примечание(1) Мнение автора карточкиТематики
- кабели, провода...
EN
- bundled cable
- multi-pole cable
- multiconductor cable
- multicore cable
- multiple cable
- multiple-conductor cable
- multiple-core cable
- multistrand cable
- N-conductor cable
- polycore cable
DE
- mehradriges Kabel, n
- Mehrleiterkabel, n
FR
Русско-французский словарь нормативно-технической терминологии > многожильный кабель
-
2 длительный допустимый ток
- courant permanent admissible, m
- courant admissible, m
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Русско-французский словарь нормативно-технической терминологии > длительный допустимый ток
См. также в других словарях:
Cable — For other uses, see Cable (disambiguation). 6 inch (15 cm) outside diameter, oil cooled cables, traversing the Grand Coulee Dam throughout. An example of a heavy cable for power transmission … Wikipedia
Coaxial cable — RG 59 flexible coaxial cable composed of: A: outer plastic sheath B: woven copper shield C: inner dielectric insulator D: copper core Coaxial cable, or coax, has an inner conductor surrounded by a flexible, tubular insulating layer, surrounded by … Wikipedia
Copper wire and cable — Copper has been used in electric wiring since the invention of the electromagnet and the telegraph in the 1820s.[1][2] The invention of the telephone in 1876 proved to be another early boon for copper wire.[3] Today, despite competition from… … Wikipedia
Submarine communications cable — A cross section of a submarine communications cable. 1 Polyethylene 2 Mylar tape 3 Stranded steel wires 4 Aluminium water barrier 5 Polycarbonate 6 Copper or aluminium tube 7 Petroleum jelly 8 Optical fib … Wikipedia
Overhead cable — Pole carrying electricity, Cable TV, and telephone equipment (top to bottom), in New Zealand. Two pairs of shoes can be seen hanging from wires. An overhead cable is a cable for the transmission of information, laid on utility poles. Overhead… … Wikipedia
многожильный кабель — многожильный провод многожильный шнур Кабель (провод, шнур), в котором число жил более трех. [ГОСТ 15845 80] EN multicore cable cable having more than one core Note – The French term «câble multipolaire» is more… … Справочник технического переводчика
Parallel ATA — ATA connector on the right, with two motherboard ATA sockets on the left. Type … Wikipedia
Modular connector — This article is about modular connectors. For the registered jack (RJ) wiring standard, see registered jack. Left to right, modular connectors: 8P8C plug, 6P6C plug, 6P4C plug, 4P4C plug, 6P6C jack … Wikipedia
AT Attachment — Infobox connector name=AT Attachment with Packet Interface type=Internal storage device connector logo= caption=ATA connector on the left, with two motherboard ATA connectors on the right. designer=Western Digital, subsequently amended by many… … Wikipedia
Twisted pair — 25 pair color code Chart Twisted pair cabling is a type of wiring in which two conductors (the forward and return conductors of a single circuit) are twisted together for the purposes of canceling out electromagnetic interference (EMI) from… … Wikipedia
National Electrical Code — The National Electrical Code, 2008 edition The National Electrical Code (NEC), or NFPA 70, is a regionally adoptable standard for the safe installation of electrical wiring and equipment. The NEC, while having no legally binding regulation as… … Wikipedia
